12/25/2024 updated

AS
100 % available

Consultant, Embedded Developer, Electronics Designer

Hjulsta, Sweden
Worldwide
M.Sc. Integrated Electronics System Design
Hjulsta, Sweden
Worldwide
M.Sc. Integrated Electronics System Design

Profile attachments

CV_Ahsan__.pdf

» Firmware Development
» Analog/Digital Electronics Design
» EMC Design
» FPGA Design (Verilog-HDL & VHDL)
» System-Level Architecture Design
» C-Language, TCL, MATLAB, LabVIEW
» Fixed Point Arithmetic
» Test/Debug Embedded Systems
» Power Supply Design
» Project Management and Scheduling

Experience

Professional experience10+ years
Freelancer since2017

Languages

EnglishFluent

Project history

Design Engineer

Logithoroughfare AB

< 10 team member

 Worked in Q.ANT GmbH on an assignment from March 2024 to August 2024.
  • Developed an embedded application on 32-bit PSoC™ 6 Arm® Cortex®-M4/M0+. The system consists of a FAN controller operated through UART, port expanders, power supplies and EEPROM connected on I2C interface and an FPGA connected with SPI. Work also includes some testing, simulation and debugging FPGA RTL by Chipscope ILA and measurement on electronics. Also developed RTL for a pattern generator and did some changes in existing RTL.
 Worked in Micropower Group AB on an assignment from June 2023 to February 2024.
  • Tested high-power chargers (3KW to 25KW) for industrial batteries of different types. This includes measurement of efficiency, performance and reliability at different temperatures, grid voltages and load conditions. Used equipment like grid emulator, power analyzer, insulation tester, transient generator, and electronic/resistive loads.
 Worked in SHL Healthcare AB on an assignment in April 2023.
  • Developed electronics schematics for air pressure-controlled mattress systems including valves, GPRS/GSM, and FPGA.
 Worked in Husqvarna AB on an assignment (from March 2021 to April 2023).
  • Developed firmware of different products by writing parts of the top-level application. Did parameterization of motor control software for controlling motors of different products like blowers, trimmers, and chainsaws.
  • Developed firmware for ICT of the PCBs in production.
  • Did PCB design for an automatic power control circuit using Altium CircuitMaker. The task includes schematics, layout, and testing of the system.

Electronics Design Consultant

Self Employed; Loginofare GmbH

Industry & Mechanical Engineering

< 10 team member

Worked in Hilti AG on an assignment through Techexperts4you AG (from January 2019 to November 2019).
* Setup of a new production line. Responsibilities were electronics development, system testing, project management, technical writing, and supplier communication. The system includes a microprocessor, acceleration sensor, RFID, BLE and a user interface with E Ink display and buttons.

Design Engineer

Self Employed; Logithoroughfare AB

Industry & Mechanical Engineering

< 10 team member

Worked in 3M Peltor Svenska AB on an assignment Sigma Technology Mid AB (from May 2017 to December 2018).
* Did firmware development on ARM-based processors for establishing a network with multiple BLE devices and routing data traffic of commands and responses from wireless modules. Different low profile, battery-operated PCBs have also been designed and tested.
* Did PCB design for different projects which includes the design of power supplies, amplifiers, and audio electronics. It also includes bring-up of electronics, low profile SMD
soldering, and Bluetooth qualification tests.

Consultant

ALTEN Sweden AB

Industry & Mechanical Engineering

1000-5000 team member

* Worked with different companies named Kongsberg Automotive AB, Cobham Gaisler AB, and Unique Pyrotechnic AB. In housework includes the design of analog and digital electronics for current measurements on ignition coils, integration for RMS value of current and control using operational amplifiers. Developed a converter module for power line communication on a customized RS485 interface from a referenced design. Did calibration and testing in the production of the units.

* Did PCB design for seat heaters with LIN interface for JLR. Did documentation at different stages of design/development like FMEA, HWDD and test specifications. Testing
of electronics according to automotive standards and environments.

Design/Test Engineer

INRESOL AB

Industry & Mechanical Engineering

10-50 team member

* Development of an automation solution for Sterling Engine which includes three-phase inverters and firmware development on DSPIC processor by Microchip. Motor control inverter for PMSM motor has been designed with the capability of 5.5 K watt of power (565V and 10A). Isolated off-the-shelf DC to DC (330V to 12V) has been selected and used. The system also includes the battery management system and a grid inverter. Did project management.

Senior Design Engineer

Bitidentify Sweden AB

Industry & Mechanical Engineering

< 10 team member

* Developed a solution for cyber hacking from specification to end system design on FPGA.
* Designed several state machines for controlling and modifying the traffic of a storage device attached to the SATA-III interface according to the SATA specification and requirements of the concept. Implemented behaviour as a pseudo-SATA host and device between the SATA host controller and SATA device controller. Designed test cases for simulation and testing using ChipScope on off-the-shelf FPGA boards.
* Did management by the scheduling of the project and implemented the solution on off-the-shelf hardware consisting of an FPGA board and computer system. Did demonstrations of the setup to different expected customers/investors and described system-level usage and importance.
* Responsibilities also include the schematics for high-speed interfaces, switch-mode power supply, EMC design and connections to a computer motherboard.

Design Engineer

EUR AB

Industry & Mechanical Engineering

< 10 team member

* Developed firmware for ARM7 and Cortex-M3 processors. A MATLAB algorithm for assessment of adverse health effects in the lumbar spine due to multiple shocks was implemented on a Cortex-M3 processor. The system includes RF transceiver, accelerometer and flash memory.

International Scholar

IMEC (Interuniversity Microelectronics Center)

Industry & Mechanical Engineering

* Validated a mixed-signal ASIC of sigma-delta modulator. Developed low noise and low distortion electronic circuits, data acquisition setup and FFT based performance analysis using MATLAB and LabVIEW. SNR of the input signal, acceptable jitter of the sampling clock, requirements of noise on the power supplies, signal integrity, and EMC
are investigated and implemented. Digital interface (Customized SPI) of the modulator chip is being programmed with MSP430 for configuring different modes

Design Engineer

CARE (Center for Advanced Research in Engineering) Pvt. Ltd.

Industry & Mechanical Engineering

50-250 team member

* Developed a software application of GSM / GPRS module for GPRS communication link from a referenced application.
* Designed a 6-Layer PCB for a Vehicle Tracking System.

Assistant Manager Technical

Margalla Electronics

Industry & Mechanical Engineering

* Converted MATLAB algorithms to "Floating Point" / "Fixed Point" C-Language. Analysis of different kinds of FPGA’s architectures was done to fulfill area and speed
requirements.
* Developed a software application for high-speed data acquisition of an "IF Modulated" signal in C-language and MATLAB using provided libraries of the data acquisition card.

Design Engineer

CARE (Center for Advanced Research in Engineering) Pvt. Ltd.

Industry & Mechanical Engineering

* A micro-coded state machine is designed in Verilog-HDL for configuring DMA of SATA controllers. Drivers for interfaces of FPGA with ADC, DAC, SRAM, and μ-Controller is designed in Verilog-HDL.
* Designed 8-Layer PCB for a Digital Signal Recorder. It also includes programming for driver routines of SATA controller, embedded file system of hard drive and a textual user interface with LCD and keypad.

Assistant Manager

Bahawalpur Engineering Private Limited

Industry & Mechanical Engineering

50-250 team member

* Responsibilities were μ-Controller (8051) programming, digital circuit PCB design, debugging and power electronics.

Contact form

Log in to get in touch

You need to be logged in to use the contact form.

Sign upLog in